Quantcast
Channel: System Center – RONNIPEDERSEN.COM
Viewing all articles
Browse latest Browse all 30

Installing SCCM 2012 SP2/R2 SP1 – Quick Start Guide

0
0

Introduction

Installing this service pack is very similar to previous service packs and CU updates but there are a few things you should be aware of. In this blog post, I’ll walk you through the upgrade process step-by-step in a SCCM 2012 R2 standalone primary scenario.

As always, you should start by checking the health of the system, verify the backup, etc.

At a minimum, you should check the following:

Download the update

After we have checked that the system is healthy, we need to download the update. SCCM 2012 SP2 / R2 SP1 is available for download here: https://www.microsoft.com/en-us/evalcenter/evaluate-system-center-2012-r2-configuration-manager-and-endpoint-protection.
The only version available today is the “Evaluation version”, but Microsoft doesn’t make dedicated Eval editions of Configuration Manager, so if you plan to upgrade an existing environment, you should be just fine using this version.

This update can be applied directly to the following Systems/Roles:

  • The Central Administration Site (CAS)
  • Primary Site
  • Secondary Site
  • SMS Provider
  • Configuration Manager Console

Update the Site Primary Site Server

To start the installation, log on to the Primary Site Server and run “Splash.hta “. The default settings should be ideal for most customers.

Note: You can follow the installation process in the “C:\ConfigMgrSetup.log” file.

clip_image001

On the Welcome Screen, click Install.

clip_image003

Review the “Before You Begin” Page and click Next.

clip_image005

On the Getting Started page, verify that “Upgrade this Configuration Manager site” is selected, and click Next.

clip_image007

Accept the license terms and click Next.

clip_image009

Accept all the license terms for the additional software and click Next.

clip_image011

On the Prerequisite Downloads, click Browse, and specify the path where you want to save the prerequisite files. Click Next.

clip_image013

Grab some coffee while the updated files are downloading.

clip_image014

On the Server Language Selection page you should just accept the default settings. Since this is an upgrade, your existing configuration should be the default selection. Click Next.

clip_image016

That’s also the case for the Client Language Settings, so just accept the default selection, and click Next.

clip_image018

Hey… It looks like we’re finally ready to get this thing started… Click Next.

clip_image020

Well… Almost. First we need to make sure that our system is healthy and is ready to upgrade. In my case I’m a little low on memory, but since this is my test lab with less than 10 clients, I’m really not worried, so I’ll click Begin Install.

clip_image022

On the Upgrade page, make sure to click “View Log”. This will open the setup log file and allow you to monitor the process as we move forward.

clip_image024

As promised… Much more fun in here Smiley

clip_image026

Finally the upgrade is complete (In my lab, it took 49 minutes) and so far everything looks great. Looking in the log file we can see that the process is complete, but the UI is not always (rarely) updated when the Upgrade is complete. After reviewing the log file, click OK.

clip_image028

Verify that the setup was successful

After the setup is complete, there are a few things you can and should do to verify that the setup was successful.

The first thing you should do is check the log file. But if you followed this guide, you have already done that. Smiley

The next thing you should do is Launch the System Center 2012 R2 Configuration Manager Console directly on the Site Server and verify the build number of the console. If the upgrade was successful, the build number should be 5.0.8239.1000.

Also note that you can now see the version number of the site server here too.

clip_image030

If you right-click and select “Properties” of the Primary Site to check the version number, you will notice that the build number is 5.00.8239.1000 (R2 SP1 RTM).

clip_image031

An overview of all versions and build numbers can be found here: http://www.ronnipedersen.com/2014/07/configmgr-2012-versionbuild-numbers/

For additional verification, you may also check the CULevel registry data under HKLM\Software\Microsoft\SMS\Setup\. If the upgrade was successful, the value should now be “0”.

clip_image033

Updating Clients

You can upgrade the clients using many different methods, but in this example, I’ll go for the Automatic Client Upgrade feature. Since this is a very small lab, I’ll set the maximums days to 1.

If you want to learn more about this feature and how it works, you should check out this blog post:
http://www.ronnipedersen.com/2014/08/sccm-2012-how-does-automatic-client-upgrade-work/

clip_image034

Monitoring the client upgrade process

There are many ways to monitor the client upgrade process, but I prefer to use the built-in report that shows the count of System Center Configuration Manager Clients by Client Version.

clip_image036

That’s it…

Next week, I’ll start to upgrade customers to this new Service Pack. As I move along and learn more, I’ll update this post with my newfound knowledge.

Until next time….

+Ronni Pedersen

The post Installing SCCM 2012 SP2/R2 SP1 – Quick Start Guide appeared first on RONNIPEDERSEN.COM.


Viewing all articles
Browse latest Browse all 30

Latest Images

Trending Articles





Latest Images